Form­work is the ele­ment that makes it pos­si­ble to build any build­ing or struc­ture, but it is also one of the most impor­tant build­ing ele­ments. Thanks to the form­work, it is pos­si­ble to erect mono­lith­ic and pre­fab­ri­cat­ed struc­tures. On the web­site https://www.formpark.ru/catalog/smazki/ you can order lubri­cant for form­work and forms of var­i­ous for­mats.

What is form­work lubri­cant for?

Why cov­er the form­work with oil? Using this tech­nique, you can not only improve the prop­er­ties of the form­work, but also sig­nif­i­cant­ly extend its life. In addi­tion, the oil gives the form­work an aes­thet­ic appear­ance, and also increas­es the mois­ture and water­proof­ing prop­er­ties. In this regard, oil is often used for water­proof­ing form­work. Oiled form­work will last much longer if you fol­low a num­ber of the fol­low­ing rules:

  • apply oil in a warm room, because in a cold envi­ron­ment it can hard­en;

  • the oil must be com­plete­ly dis­solved in water (at least 50%). Only in this case it will be even­ly dis­trib­uted over the sur­face;

  • Do not dilute the oil with water dur­ing use. It is bet­ter to use it imme­di­ate­ly after prepa­ra­tion; it is best to apply the oil in an even lay­er on a smooth sur­face, while the excess is best removed before it dries;

  • when applied, the oil should be even­ly dis­trib­uted over the entire sur­face, and not just in the recess­es.

When apply­ing, it is rec­om­mend­ed to use a wide brush or roller. All irreg­u­lar­i­ties must be lev­eled by rub­bing or soak­ing oil. If dur­ing oper­a­tion the form­work begins to lose its prop­er­ties, then the oil should be applied again.

Formwork lubrication

What to look out for

The oil is water­proof, so it is not afraid of any pre­cip­i­ta­tion. It is able to pro­tect the form­work from mois­ture and damp­ness for a long time. If the room in which the form­work is locat­ed is con­stant­ly exposed to water, it is rec­om­mend­ed to peri­od­i­cal­ly treat it with oil. After com­ple­tion of con­struc­tion work, it is nec­es­sary to thor­ough­ly rinse the form­work due to the fact that it con­tains the remains of con­crete and oth­er build­ing mate­ri­als.

There­fore, before start­ing to use the form­work for its intend­ed pur­pose, it must be cleaned of dirt and dried. Do not for­get that wood­en ele­ments are sub­ject to decay. This can be avoid­ed by peri­od­i­cal­ly apply­ing spe­cial oil to them. Form­work oils are a ver­sa­tile mate­r­i­al, the use of which can be eas­i­ly explained from a sci­en­tif­ic point of view. The oils used in the man­u­fac­ture of form­work have the fol­low­ing prop­er­ties:

  • first­ly, they give form­work sur­faces addi­tion­al water tight­ness;

  • sec­ond­ly, they reduce heat trans­fer through the form­work;

  • third­ly, they pro­vide good per­for­mance prop­er­ties.

Thus, the use of oil in the man­u­fac­ture of form­work sur­faces allows us to solve all the tasks set for pro­duc­tion.

Source: TopClimat.com