[ad_1]

Best Vibratory Pumps 2022

A pump for a sum­mer house or a small pri­vate house should be reli­able, sim­ple and always inex­pen­sive. These con­di­tions are ful­ly sat­is­fied by vibra­tion sub­mersible pumps.
Best Vibratory Pumps 2022
The best vibra­tion pumps. Pho­to: shutterstock.com

A vibra­tion pump is a sub­species of a sub­mersible pump: it is com­plete­ly immersed in a liq­uid and sus­pend­ed on a cable. Pow­er is sup­plied to it via a rub­ber­ized cable, water goes up through an armored hose. The design does not have an elec­tric motor and an impeller, how­ev­er, such a sim­ple device reg­u­lar­ly pumps water from any reser­voir, well or well. This type of pump is rel­a­tive­ly inex­pen­sive.

Top 10 rating according to KP

1. QUATTRO ELEMENTI Acquatico 260–10

QUATTRO ELEMENTI Acquatico 260-10
QUATTRO ELEMENTI Acquati­co 260–10. Pho­to: yandex.market.ru

The diam­e­ter of the pump is 120 mm, it copes well with the sup­ply of water from wells and wells. Alu­minum alloy body will not cor­rode. The unit is equipped with over­heat­ing pro­tec­tion. The upper water intake pre­vents sand and clay from enter­ing the work­ing cham­ber.

Characteristics

Per­for­mance 1.08 cu. m/h
pres­sure 60 m
Immer­sion depth 2 m
The weight 3.2 kg
Guar­an­tee 1 year

Pros and cons

Over­heat­ing pro­tec­tion, non-cor­ro­sive hous­ing
For pure water only

2. PATRIOT VP-16V

PATRIOT VP-16V
PATRIOT VP-16B. Pho­to: yandex.market.ru

The main dif­fer­ence from the pre­vi­ous mod­el is the case diam­e­ter of 100 mm. This allows you to pump water from wells with a small­er pipe diam­e­ter. Oth­er tech­ni­cal char­ac­ter­is­tics are sim­i­lar, but the pres­sure is notice­ably high­er.

>

>

Characteristics

Per­for­mance 1.08 cu. m/h
pres­sure 72 m
Immer­sion depth 7 m
The weight 3.7 kg
Guar­an­tee 1 year

Pros and cons

Dry run­ning pro­tec­tion, 25 m elec­tric cable
For pure water only

3. BELAMOS Cricket BV-V-50

BELAMOS Cricket BV-V-50
BELAMOS Crick­et BV-V-50. Pho­to: yandex.market.ru

Reli­able and easy to main­tain unit. The long elec­tric cable includ­ed in the kit allows you to con­nect to the net­work with­out an exten­sion cord. Mod­els with upper and low­er water intake are avail­able.

Characteristics

Per­for­mance 0.96 cu. m/h
pres­sure 70 m
Immer­sion depth 3m
The weight 2.6 kg
Guar­an­tee 1 year

Pros and cons

Over­heat­ing pro­tec­tion, selec­table liq­uid intake direc­tion, 25 m elec­tric cable
Not detect­ed

4. Vortex VN-10N

Whirlwind VN-10N
Whirl­wind VN-10N. Pho­to: yandex.market.ru

Pro­duc­tiv­i­ty is high, the upper water intake cuts off sand and dirt. Reli­able ther­mal pro­tec­tion saves the unit dur­ing long-term oper­a­tion. Users note the qui­et oper­a­tion of the device.

Characteristics

Per­for­mance 1.08 cu. m/h
pres­sure 72 m
Immer­sion depth 3m
The weight 2.6 kg
Guar­an­tee 1 year

Pros and cons

Over­heat­ing pro­tec­tion, qui­et oper­a­tion
For pure water only
It is inter­est­ing

For­got your pass­word again? Mobile ID will help

5. LEPSE Aquarius‑3 10 m

LEPSE Aquarius-3 10m
LEPSE Aquarius‑3 10m. Pho­to: yandex.market.ru

The low­er half of the pump hous­ing is made of rub­ber. This reduces vibra­tion and pre­vents dam­age when low­er­ing into a deep well. The kit includes a steel cable for sus­pen­sion. Main­te­nance is sim­ple, no spe­cial tools are need­ed for dis­as­sem­bly.

The pump is equipped with a well-thought-out pro­tec­tion sys­tem. The engine stops not only when over­heat­ing, but also when the hose is bent or the work­ing cham­ber is clogged.

Characteristics

Per­for­mance 1 cu. m/h
pres­sure 80 m
Immer­sion depth 40 m
The weight 4 kg
Guar­an­tee 1 year

Pros and cons

Robust steel loop for secur­ing the cable, reli­able pro­tec­tion sys­tem, part­ly rub­ber hous­ing
Net­work cable not long enough

6. Livgidromash Malysh‑M

Livgidromash Malysh-M
Livgidro­mash Malysh‑M. Pho­to: yandex.market.ru

An eco­nom­ic and unpre­ten­tious pump with the top liq­uid intake. The wind­ing of the elec­tro­mag­net is made of cop­per, so it works for a long time with­out over­heat­ing. The silu­min case per­fect­ly pro­tects the inter­nal parts from dam­age. More­over, it also does not rust.

Characteristics

Per­for­mance 1.5 cu. m/h
pres­sure 60 m
Immer­sion depth 3m
The weight 3.4 kg
Guar­an­tee 1.5 years

Pros and cons

Over­heat­ing pro­tec­tion, silu­min hous­ing
Not seen

7. UNIPUMP BAVLENETS‑M BV 0.12–40-U5

UNIPUMP BAVLENETS-M BV 0.12-40-U5
UNIPUMP BAVLENETS‑M BV 0.12–40-U5. Pho­to: yandex.market.ru

Eco­nom­i­cal pump with stain­less steel cas­ing and water­proof­ing to IP68. Avail­able in two ver­sions with top or bot­tom intake. There is enough pres­sure to sup­ply water to a three-sto­ry house with a stor­age tank in the attic.

Characteristics

Per­for­mance 1.6 cu. m/h
pres­sure 80 m
Immer­sion depth 40 m
The weight 3.5 kg
Guar­an­tee 1 year

Pros and cons

Choice of mod­els with top or bot­tom water intake, strong pres­sure
High price

8. Technopribor Brook‑1

Technopribor Rucheyok-1
Techno­pri­bor Brook‑1. Pho­to: yandex.market.ru

The com­pact unit in an all-met­al hous­ing rais­es water to a height of 60 m. The upper liq­uid intake pro­tects the work­ing cham­ber from con­t­a­m­i­na­tion. There is ther­mal pro­tec­tion.

Characteristics

Per­for­mance 1.05 cu. m/h
pres­sure 60 m
Immer­sion depth 3m
The weight 3.6 kg
Guar­an­tee 1 year

Pros and cons

Over­heat­ing pro­tec­tion, steel case
Net­work cable not long enough, only 10 m

9. JILEX Poplar Malysh‑M 16 m

JILEX Poplar Malysh-M 16 m
JILEX Poplar Malysh‑M 16 m. Pho­to: yandex.market.ru

The pump is domes­tic, pro­duced in Livny. Spare parts for it can be bought in all cities of the coun­try. The diam­e­ter of the steel body is only 9.8 cm, it pass­es even the nar­row­est wells. Lev­el of hydropro­tec­tion of the body IP68. Starts to work at water tem­per­a­ture from +1 degree Cel­sius.

Characteristics

Per­for­mance 1.5 cu. m/h
pres­sure 60 m
Immer­sion depth 3m
The weight 3.6 kg
Guar­an­tee 1.5 years

Pros and cons

Low water tem­per­a­ture accept­able, upper liq­uid intake, steel body
Strict­ly ver­ti­cal work­ing posi­tion

10. Zubr ZNVP-300–10_M2

Zubr ZNVP-300-10_M2
Bison ZNVP-300–10_M2. Pho­to: yandex.market.ru

The pump is unpre­ten­tious and reli­able. Dif­fers in low pow­er con­sump­tion. Up to 200 hours of con­tin­u­ous use, dou­ble that of oth­er mod­els. The upper water intake pre­vents clog­ging of the work­ing cham­ber. Per­mis­si­ble size of sol­id par­ti­cles in water up to 2 mm.

Characteristics

Per­for­mance 1.44 cu. m/h
pres­sure 60 m
Immer­sion depth 3m
The weight 4.5 kg
Guar­an­tee 1 year

Pros and cons

Upper liq­uid intake, work with con­t­a­m­i­nat­ed water, check valve pre­vent­ing liq­uid from drain­ing when the well is emp­ty, cop­per wind­ing of the sta­tor coil, steel case
High noise lev­el
Read also

The best pump­ing sta­tions for the home

How to choose a vibration pump

The pow­er unit of any vibra­tion pump is an elec­tro­mag­net con­sist­ing of a U‑shaped steel core with a cop­per wire wind­ing. It is sup­plied with alter­nat­ing cur­rent with a volt­age of 220 V. As a result, an elec­tro­mag­net­ic field with a fre­quen­cy of 100 Hz is cre­at­ed. The core and coil are insu­lat­ed with epoxy to pre­vent water pen­e­tra­tion.

>

>

The arma­ture under the influ­ence of an elec­tro­mag­net­ic field moves in the coil, then returns to its pre­vi­ous posi­tion. The move­ments are small, resem­bling vibra­tion. They are trans­ferred to a rod with a rub­ber wash­er installed at the oppo­site end, which plays the role of a pis­ton. The per­for­mance and dura­bil­i­ty of the entire unit depends on its qual­i­ty. The rod togeth­er with the pis­ton vibrates inside the injec­tion cham­ber, suck­ing water from the source and squeez­ing it out.

Liq­uid enters the cham­ber through check valves at the bot­tom of the hous­ing. They do not allow water to be squeezed back, leav­ing it one way — to the out­let pipe. The device has prac­ti­cal­ly no mov­ing parts that require peri­od­ic main­te­nance or pre­ven­tive main­te­nance.

Despite the com­mon­al­i­ty of the design, spe­cif­ic types of pumps dif­fer great­ly in their char­ac­ter­is­tics. Kom­so­mol­skaya Prav­da turned to the online hyper­mar­ket expert Max­im Sokolov for help in choos­ing the device you need.

Read also

The best sew­er pumps

When choos­ing a sub­mersible vibra­tion pump, you need to pay atten­tion to the fol­low­ing para­me­ters:

  • Per­for­mance shows the vol­ume of water that the pump is able to pump per unit of time. For a pre­lim­i­nary cal­cu­la­tion of the required val­ue of this indi­ca­tor, there are spe­cial tables. They take into account the num­ber of water flow points in the form of sprin­klers or sinks in the house, plus the deb­it of the well indi­cat­ed in her pass­port. The min­i­mum suf­fi­cient to ensure irri­ga­tion and the dai­ly needs of sum­mer res­i­dents is 360 l / h. A coun­try house will need 1500 l / h. There are mod­els that can pro­vide twice as much pro­duc­tiv­i­ty, up to 3000 l / h. Do not use a pump with a capac­i­ty greater than the flow rate of the well. This will lead to its peri­od­ic dry­ing and wash­ing out of clay par­ti­cles, which will quick­ly dis­able the pump.
  • pres­sure char­ac­ter­izes the dis­tance to which the pump is able to deliv­er water. This indi­ca­tor varies from 40 to 90 m. To cal­cu­late, it is nec­es­sary to add up the immer­sion depth, the dis­tance between the sur­face of the water in the well and the ground lev­el, the length and height of the water sup­ply to the end points of flow. And then add anoth­er 20% to the result­ing val­ue. The pres­sure is nev­er too much. The out­side diam­e­ter of the body must be small­er than the inside diam­e­ter of the well cas­ing.
  • ther­mal pro­tec­tion nec­es­sary in order to ensure that the pump is turned off when the water source is drained. In this case, the elec­tro­mag­net coil will fail due to over­heat­ing.
  • Also desir­able dry run pro­tec­tionthat is, turn­ing on the pump in the absence of water.
  • Water intake loca­tion. The pump inlet can be locat­ed at the top or bot­tom of the cas­ing. In the first case, sand and clay from the bot­tom will not get into the water; such pumps are good for sup­ply­ing water from wells and open reser­voirs. They must be installed at a dis­tance of more than 30 cm from the bot­tom. The sec­ond type of design is most often used in bore­hole pumps, because it allows to reduce the size of the cas­ing to a min­i­mum. But a min­i­mum of a meter of water-filled well below the inlet fil­ter is required.

A vibra­tion pump is a reli­able and sim­ple unit that will sup­ply your home or cot­tage with water with­out undue cost and effort. The cor­rect choice and obser­vance of the oper­at­ing instruc­tions is a guar­an­tee that it will work for more than one year.

>

>